履帶式陶瓷加熱器是採用強度高,熱輻射性能好的氧化鉛陶瓷元件作絕緣材料,用鎳鉻絲纜作發熱體,穿接好的加熱器可以是矩形或三角形。鎳鉻絲纜與導線採用新工藝焊接,焊接的接頭全部埋入陶瓷元件內絕緣可靠,陶瓷加熱器與控製設備配套即成為完整的熱處理係統,它們的連接採用專用接插件,並可根據工件與控製設備的距離配置接長導線。長度尺寸可以靈活改變製作的履帶式陶瓷加熱器。
特點
1.具有繞性,如加熱容器或管道時,可彎麯成弧形或圓形包複在錶麵加熱,如加熱大型工件,局部可採包複形式,大麵積工作可採用平鋪複蓋形式。此外能適合各種幾何形狀工件的加熱。
2.工作溫度高,升溫快,熱效率高,無汙染,加熱均勻準確,可以實現自動控製。
3.機械強度高,熱態絕緣性能好,與被加熱物體接觸麵大,使用壽命長。
4.安裝,維修方便,使用費用低,即使內部發熱材料損壞,而外部的陶瓷器件仍可回用。長度尺寸可以靈活改變製作的履帶式陶瓷加熱器,應視工件的幾何形狀,壁厚及熱處理工藝選擇相應的規格,下錶僅列部分規格。
應用:主要用於塑料工業註塑機、擠出機和吹塑機的加熱,同時也可用於反應釜、熔體管道等化工領域的加熱。
結構:採用Ni80Cr20電阻絲插入陶瓷內孔,整個加熱體柔軟可塑,升溫迅速,加熱均勻,節能及較長的使用壽命。金屬外殼採用不鏽鋼闆或鍍鋁鋼闆製作。
技術參數:工作溫度可達760℃,功率密度可高至8w/cm2。陶瓷加熱圈的直徑為40mm,直徑大於600mm時,應分成2-8個弧段加熱,採用壓力彈簧夾緊。加熱器的寬度為18mm,以7.5mm為進階(18、25.5、33、40.5、48mm……)寬度不應大於500mm,加熱體的厚度為12mm,如需加保溫層,加熱體的厚度會根據保溫層厚度增大,請考慮安裝空間。
電源接線方式
1.插頭式接線(*大20A);
2.接線盒式接線(可多相固定連接);
3.高溫線引出式接線(屏蔽耐熱純鎳導線)。
It is mainly applied to heating the plastic injection molding machine, extruding machine and blowing machine. Meantime, it also can be used to heat reaction kettle, melt pipe, etc in chemical industry.
Structure
Ni80Cr20 resistance wire is inserted into ceramic inner hole. The whole heating body is soft & mouldable, energy-saving and durable. Furthermore, it is heated up quickly and evenly. The metal shell is made of stainless steel plate or galvanized steel plate.
Technical Parameter
The working temperature can be up to 760℃ and the power density 8w/cm2. The minimum diameter of ceramic heating ring is 40mm.
When the diameter is larger than 600mm, the ring, clamped by pressure spring, should be separated int0 2-8 segmental arc to be heated. On the other hand, the minimum width of the heater is 18mm and the maximum width of that should not be more than 500mm, increasing by 7.5mm (1 8,25.5,33,40.5,48mm...). The thickness of the heating body is 12mm. If adding thermal insulation layer, the thickness of the heating body increases accordingly. Please take installation space into consideration.